Heat Siphon Heat Pump Error Codes

Doing some Heat Siphon heat pump troubleshooting?

These Heat Siphon heat pump error code explanations will help you fix some of the most common Heat Siphon pool heater problems:

heat siphon heat pump error codes heat siphon heat pump troubleshooting codes heat siphon pool heaters

Heat Siphon Heat Pump Error Codes

 

Need help troubleshooting or repairing your pool heater?

Yes, let’s get started

 

Heat Siphon heat pump error code Lo P | Lo A

(My Heat Siphon heat pump says Lo P)

Lo P | Lo A

What it means: 

Lo P: the refrigerant system’s low-pressure sensor detects low refrigerant, low air flow, or low air temperature

Lo A: the low-pressure switch was triggered and outside air temperature is under 50 degrees

How to fix it:

  • Make sure pool pump is receiving enough water
  • Check that pool pump is sending water to the heat pump
  • If possible, put the pump speed up a notch
  • Check for any clogs or backups causing poor water circulation
  • For refrigerant leaks and continuous sensor or fan issues, seek professional pool heat pump repair service

 

Heat Siphon heat pump error code Hi P

Hi P

What it means: refrigerant system’s high-pressure switch triggered

How to fix it:

 

Heat Siphon heat pump error code Lo / FLO

Lo / FLO

What it means: sensor detecting restricted or low water flow

How to fix it:

  • Check for, and clear out any blockage in the baskets (pump, skimmer) and filter system
  • Call pool heating to inspect the water pressure sensor

 

Heat Siphon heat pump error code SH o | SH S

SH o | SH S

What it means: 

SH o: water temperature thermistor is open or has damaged wiring

SH S: thermistor has short circuited

How to fix it:

  • Have a pool heat pump tech inspect the thermistor
  • If shorted, replace the thermistor

 

Heat Siphon heat pump error code H i / UoLt | L o / UoLt

H i / UoLt | L o / UoLt

What it means: 

H i / UoLt: high voltage being received from transformer (more than 31.2 VAC)

L o / UoLt: low voltage being received from transformer (less than 19.2 VAC)

How to fix it:

  • Visually inspect the heater’s electrical connection for any damage or corrosion
  • Seek professional assistance for correcting the wiring issue

 

Heat Siphon heat pump error code HS S | HS o

HS S | HS o

What it means: 

HS S: main contactor coil has shorted

HS o: open contactor coil, or no resistance detected

How to fix it:

  • Have unit inspected for wire or coil damage. Replace as necessary

 

Heat Siphon heat pump error code CAnt / HEAt

CAnt \ HEAt

What it means: pump has been running for over 24 hours with no temperature gain. Possible causes include an undersized heater, heat loss, or cold air temperature.

How to fix it:

  • Use a solar cover to alleviate heat loss
  • Problem should resolve once possible causes have been addressed

 

Heat Siphon heat pump error code SA o | SA S

SA o | SA S

What it means: low-pressure sensor in refrigerant system may be open

How to fix it:

  • Replace thermistor
  • If problem persists, replace board

 

Heat Siphon heat pump error code no / Pod

no / Pod

What it means: pump is searching for external pod controller and cannot find it

How to fix it:

  • Power off the heat pump to clear the error code

 

Heat Siphon heat pump error code Air / Hi

Air / Hi

What it means: old error code for detecting board temperature

How to fix it:

  • Seek manufacturer for board software update

 

Heat Siphon heat pump error code CH o | CH S

CH o | CH S

What it means:

CH o: reversing valve coil has an open circuit

CH S: reversing valve coil has short circuited

How to fix it:

  • Inspect wiring for damage
  • If shorted, replace reversing valve coil

 

The following error codes are for circuit board issues and should be fixed by a professional

 

Heat Siphon heat pump error code Brd1

What it means: Heat Siphon board has shorted

 

Heat Siphon heat pump error code Brd2

What it means: reversing valve board short

 

Heat Siphon heat pump error code Brd3

What it means: POD board short

 

Heat Siphon heat pump error code Brd4

What it means: loose wires in control panel

 

Heat Siphon heat pump error code Brd5

What it means: loose connection or screw on reversing valve